電壓擊穿試驗儀-擊穿電壓儀 安裝條件：
電源： 220V±10%的單相交流電壓和50Hz±1%的頻率
10、電源電壓穩定度外界電源電壓波動≤10%
11發揮作用、長×寬×高700mm×800mm×1650mm
12良好、設備自重： 100kg
13、運行環境溫度：15 ～ 30℃銘記囑托，相對濕度：30%～85%能夠穩定運行引領。
14、接地要求儀器需要單獨接地示範，接地附合國家標準要求
15應用前景、接地電阻要求≤4Ω（用戶實驗室自行準備）
電壓擊穿試驗儀-擊穿電壓儀技術參數
1 試驗變壓器
1.1 輸出電壓： AC ?0-10000V，DC 0-10000V運行好；
1.2 輸入電壓：220v
1.3 額定容量下首次，長期連續運行；
1.4 zui大輸出電壓下部署安排，PD≤1pC搖籃；
1.5 噪聲≤58dB（1m位置測量）。
2 調壓器
2.1 輸入電壓：220V推廣開來；
2.2 額定容量：2kVA（如果有補償推動，可以小于15kVA，但不小于10kVA）資源配置；
2.3額定容量下信息，長期連續運行；
2.4噪聲≤58dB（1m位置測量）;
2.5 電動調壓大力發展。
3 高壓分壓器
3.1 高壓臂電容：1nF豐富內涵；
3.2 分壓比：700（可討論，結合測量控制系統）不同需求；
3.3 額定容量下發展，長期連續運行；
3.4 zui大輸出電壓下總之，PD≤1pC面向；
3.5 測量精度：1%。
4 計算機控制
4.1 藍牙連接同時；
4.2 安全保護互動式宣講；
5 試驗電極
5.1 滿足GB/T 1408-2006 絕緣材料電氣強度試驗方法效高性；
5.2 滿足GB/T 1695-2005 硫化橡膠工頻電壓擊穿強度和耐壓強度試驗。
電壓擊穿試驗儀-擊穿電壓儀技術指標：
輸入電壓： 交流 220 V 輸出電壓： 交流 0--100 KV ;/直流 0—100 KV
電器容量： 10KVA 高壓分級： 0-100KV 升壓速率：0.01-5.0kv
（備注：滿足標準要求并可以根據用戶需求設定不同的升壓速率）
06自動化、試驗方式： 交流試驗/?直流試驗：1提升、勻速升壓? 2、梯度升壓 3不折不扣、耐壓試驗
試驗介質：空氣支撐能力，試驗油 安裝靈敏度較高的過電流保護裝置保證試樣擊穿時在0.05S內切斷電源。 儀器配備先進的故障報警系統 避免用戶操作故障儀器發生危險高效利用。（上位機報警和下位機報警
電壓擊穿試驗儀-擊穿電壓儀使電介質擊穿的電壓特征更加明顯。電介質在足夠強的電場作用下將失去其介電性能成為導體,稱為電介質擊穿,所對應的電壓稱為擊穿電壓。
電介質擊穿時的電場強度叫擊穿場強講理論。不同電介質在相同溫度下,其擊穿場強不同的可能性。當電容器介質和兩極板的距離d一定后,由U1-U2=Ed知,擊穿場強決定了擊穿電壓。擊穿場強通常又稱為電介質的介電強度服務為一體。
提高電容器的耐壓能力起關鍵作用的是電介質的介電強度問題。附表為各種電介質的相對介電常量εr和介電強度。電介質εr擊穿場強,×106/（V·m-1）
絕緣材料電壓擊穿試驗儀-擊穿電壓儀
[容量（kVA）]/[輸出電壓（ kV）]?油浸式試驗變壓器
常規型號 1.5/50 3/50 5/50 10/50
20/50 30/50 40/50 50/50 10/100
20/100 30/100 40/100 50/100 20/150
30/150 40/150 50/150 100/150 50/200
100/200 150/200 200/200 300/200 50/300
100/300 150/300 200/300 300/300
說明：以上是常規型號全會精神，也可以按照客戶特定參數定制系統穩定性。
- 擊穿試驗breakdown test; flash (ing) test; spark-over test; disruptive test
- 操作步驟operating steps
- 快捷圖標short-cut icon
- 交流電壓alternating voltage
- 高壓硅堆high voltage silicon rectifier stack; high-voltage silicon stack
- 測試回路test loop; testing loop
- 直流電壓volts d.c.; direct voltage
- 高壓變壓器high tension transformer; high-voltage transformer (HVT); high voltage transformer
- 高壓絕緣high-voltage insulation; high voltage insulation
- 測試電路test circuit; test connection
Operation procedure of voltage breakdown tester:
1. Preparation before test: 1) open the main power switch on the right side of the test machine and preheat for 15 minutes. 2) turn on the computer and enter the Windows system. Double click the instrument software shortcut icon, open the test login screen, enter the login password, you can enter the test interface.
2 、 AC and DC test switch 1) this instrument high voltage output is AC voltage. The way to obtain DC is to connect the high voltage silicon stack into the original circuit, so that the test circuit is a pulsating DC voltage. The implementation process, has been in a high voltage silicon stack transformer insulation tower, usually with a short rod, short circuit high-voltage silicon stack. When the DC test is needed, the short circuit rod is removed so that the high voltage silicon stack is connected to the test circuit, and the voltage of the circuit is a pulsating DC voltage.
2) front panel DC AC select button. The status of the button cannot change the voltage characteristic of the device output. Press this button, the device is only to connect the DC alarm circuit. Instructs the user when you open the door of the box, you need to discharge the ball evenly under high pressure. Turn off the pole so that the end of the pole is in contact with the high-pressure ball. It is recommended that each user discharge copper balls in contact with high pressure equal pressure ball for more than five seconds.
3) the AC / DC voltage switching of the test mainly depends on whether the short rod in the high voltage insulated tower is taken out. When the short circuit rod is taken out, the voltage on the ball is a direct current voltage, and when the short circuit rod is inserted, the voltage on the high voltage equalizing ball is an alternating voltage. Take out the short pole and insert it. See the diagram on the left.
4) in the DC test, the computer should also choose the DC state, otherwise the result of measurement is incorrect. In brief, the AC voltage is twice as much as the DC voltage.
Voltage breakdown test instrument is a high voltage output device. Installation, movement and use should pay special attention to the safety of people and equipment. Please note the following:
1 equipment must be connected to 16A single-phase 220V AC socket.
2 one of the two grounding terminals of the equipment must be connected to the ground wire of the distribution box through a dedicated earth wire.
3 before use, one of the two grounding terminals must be connected with the discharge rod.
4 in the test, if the observation current is maintained at 20-30mA for a long time, the test should be stopped immediay so as not to overload the fire tube.
5 a test finished, be sure to unplug the residual charge and then put off the high voltage output end of the bar.
6, in case of emergency, should immediay press "emergency stop" button, power failure.
7 do not use for a long time, disconnect all power lines.
8, handling can not tilt too large angle, so as not to transformer oil flow.
In 9 samples, make sure you've let the electric discharge rod, and the power is disconnected.
10 test process, in case of fire, be sure to break the power supply, and then extinguish the fire.
